Read Time: 10 minutes
Your boiler is on borrowed time, your engineer has just said the word “replace”, and then comes the question that sounds simple: combi or system?
Pick well and you will barely think about your boiler for years. Pick badly and you will find out on a Monday morning, when one person is in the shower and someone else turns on the kitchen tap.
The short answer: a combi boiler heats water straight from the mains whenever you open a tap, and needs no hot water cylinder or loft tank. That makes it a natural fit for flats and smaller homes. A system boiler works with a hot water cylinder, so it can supply several taps at once, which suits homes with more than one bathroom. Neither is better for every home. The right choice depends on your space, how you use hot water and the water flow you get at your property.
We have spent eight years working on boilers across London, from compact flats to family houses, and this is the conversation we have most before an installation. Here’s how we’d talk you through it.
What’s the difference between a combi and a system boiler?
The simplest way to think about it is: where does your hot water come from?
A combi (combination) boiler is a central heating boiler and a water heater in one compact unit. According to Worcester Bosch, it heats water directly from the mains when you turn on a tap, so there’s no hot water cylinder and no cold water tank in the loft. Hot water arrives at mains pressure, which can mean a strong shower without a separate pump. Worcester Bosch also points to practical wins: compact size, no cylinder taking up living space, no loft tank to freeze, and less pipework, which typically makes installation cheaper.
A system boiler works differently. Vaillant explains that a system boiler has a cylinder to store hot water for later use, while a combi only heats water on demand. Worcester Bosch adds that the main heating and hot water components are built into the boiler itself, so there’s no loft tank, and installation is quicker and neater. Because the water is stored, a system boiler can supply any number of taps at the same time, which is why it’s described as ideal for homes with more than one bathroom.
There’s a third type too, the regular (heat-only) boiler, which needs a cylinder plus tanks in the loft. We’ll come back to it below.
Which one suits my London home?
Use this as a starting point, not a verdict. It’s based on how Worcester Bosch describes each boiler type.
| Your situation | Likely fit | Why |
| One-bed or two-bed flat, little storage space | Combi | Compact, no cylinder or loft tank needed |
| Small house with one bathroom | Combi | Hot water on demand, less pipework |
| Family home with two or more bathrooms | System | Stored hot water can feed several outlets at once |
| Loft conversion planned or loft space wanted | Combi or system | Neither needs a cold water tank in the loft |
| Older radiator system, or low water pressure | Regular may be worth considering | Handles low pressure, and may suit older radiators that can’t cope with higher pressure |
Two London realities are worth keeping in mind. First, many of us have limited space, and a combi’s small footprint can be a lifesaver in a flat or maisonette. Second, the age and condition of your pipework matters as much as the boiler you choose, which we’ll get to shortly.
The question most people skip: your water flow rate
This is where combi decisions are won or lost.
A combi boiler heats the water coming into your home, so it can only deliver what the mains supplies. Worcester Bosch explains the flow rate (litres per minute of hot water at the tap) depends on the amount and pressure of water entering your property and on how well the boiler can heat it. A more powerful boiler doesn’t automatically give you more hot water. If 10 litres a minute enter your home, 10 litres a minute is the most you’ll get out of the hot tap, even from a boiler rated for more.
So before you commit to a combi, ask your installer to check the flow rate at your property. It can differ from street to street and building to building.
One small clarification, because the two get mixed up: the pressure of your mains water is a different thing from the pressure gauge on your heating system. If it’s the second that keeps dropping, our guide on why boiler pressure won’t stay up and how to repressurise will help.
When might a regular boiler still be the right answer?
Regular boilers get overlooked, but they have their place. Worcester Bosch says a regular boiler suits homes that already have a traditional heating and hot water system linked to a separate cylinder, and can be a good option where water pressure is low or where two or more bathrooms need a lot of hot water at once. It also notes that a regular boiler may be the best replacement if the property has an older radiator system that might not cope with the higher water pressure delivered by system or combi boilers.
The trade-off is space. You need the cylinder, plus a cold water tank in the loft and a tank for the heating system. If you’re short on room, that’s a real cost.
Will my old radiators and pipework cope with a new boiler?
This is the question that catches people out, and it’s worth asking before you sign anything.
Worcester Bosch is clear that if a new boiler is fitted onto an existing system, the cleanliness of the old pipework and radiators matters, because dirty system water can damage the new boiler. Over time, oxygen in the system reacts with metal and produces rust particles that circulate in the water, along with limescale. These can block and damage key components. That’s why Worcester Bosch recommends a thorough system flush when a new boiler goes onto an old system, followed by inhibitor and a system filter. It also says Building Regulations recommend fitting a system filter in the pipework before the boiler.
Our guide on whether your existing radiators and pipework will work with a new boiler goes into this in more detail.
Is it time to replace, or can the old boiler be repaired?
Sometimes a repair is the sensible call. Sometimes it isn’t. If your boiler is old and keeps failing, it’s worth knowing what you’d gain by replacing it.
Worcester Bosch says condensing boilers convert at least 90p of every £1 you spend on gas or oil into heat for your home. It also says an old, non-condensing (G-rated) boiler is likely to be around 30% less efficient than a new A-rated Worcester boiler. Your own saving will depend on your home and how you use heating, so treat that as a guide rather than a promise.
If your boiler is only a few years old, a fault is more likely to be a repair job. If you’re looking at a boiler repair in London on an older unit and the bills are mounting, ask your engineer for an honest repair-versus-replace comparison, and weigh up the cost of each, not just the first quote.
Six questions to ask your installer before you say yes
A good installer will welcome these.
- Are you Gas Safe registered, and can I see your ID? Worcester Bosch states that an installer must be on the Gas Safe Register to legally work on your boiler. You can check on the Gas Safe Register.
- Can you check the water flow rate at my property? Especially important for a combi.
- What size boiler do I need, and why? Worcester Bosch advises choosing the correct output for your home. A higher output than you need brings no benefit.
- Is a system flush and a system filter included? See above.
- Where will the flue and condensate pipe run? Worcester Bosch notes that a condensate pipe not terminated according to its installation guidelines could freeze in severe weather. Good routing at installation prevents winter callouts later.
- What guarantee comes with the boiler, and what are the conditions? Manufacturer guarantees often come with conditions. Worcester Bosch, for instance, ties its extended guarantees to specific installation requirements. Ask for the terms in writing.
After a home visit, a good installer will calculate the best system for your home and hot water needs and then give you a quote. Worcester Bosch describes each heating system as needing custom design, which is the reason a generic online price rarely tells the whole story.
Life after installation: what to expect
A new boiler isn’t a “fit and forget” purchase. Vaillant says a boiler should be serviced once a year, and that most manufacturer guarantees require it. Vaillant also says a typical annual service costs between £70 and £120 depending on the provider and area. If you have a Worcester, our team covers Worcester Boiler Service London and Worcester Boiler Repair London, so the same engineers can look after it for years.
If your new boiler ever displays a code, don’t panic. Our post on what your boiler error code is really telling you explains how to read it. And if it starts making unfamiliar sounds, this guide to boiler noises before winter will help you decide whether it’s normal or needs a visit.
Choosing a boiler in London? Talk to us
The right boiler isn’t the most expensive or the most popular. It’s the one that fits your home, your hot water habits and your pipework. Boiler Services London has spent 8 years helping homeowners across London with boiler repairs, servicing and installations, always with Gas Safe registered engineers.
If you’d like a straight answer on combi or system for your home, call us and we’ll talk you through your options.
Call us on 07877767776 or visit boilerserviceslondon.co.uk.
Frequently asked questions
A combi (combination) boiler is a central heating boiler and a water heater in one unit. It heats water directly from the mains when you turn on a tap, so you don’t need a hot water cylinder or a cold water tank in the loft.
For many flats, a combi is the natural fit because it’s compact and needs no cylinder or loft tank. The exception is a flat with several bathrooms or heavy hot water use, where a system boiler with a cylinder may cope better. Ask your installer to check your water flow rate before deciding.
A combi heats water on demand, straight from the mains. A system boiler heats water and stores it in a cylinder for later use, so it can supply several taps at once.
It’s often possible, but it isn’t a like-for-like swap, because a combi doesn’t use a cylinder and the pipework may need changing. Your installer should assess the property, including your water flow rate, before recommending it.
Only a Gas Safe registered engineer can legally work on gas boilers. Check their ID card and look them up on the Gas Safe Register before any work begins.